Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Arlington?
Replacing a gate motor and opener in Arlington typically costs $950 to $2,800 for a residential driveway gate, and $1,800 to $6,500 or more for a commercial or multi-unit slide gate system, installed. A straightforward swap of one operator on an existing gate that already has power and a working control setup usually lands near the low end; a full system with new access hardware, safety sensors, and wiring runs toward the high end. The written estimate you get after an on-site look sets the final price, and that estimate is free.
Those numbers cover the operator itself, the labor to hang and dial it in, and the safety gear most Arlington properties need to pass inspection. What they don’t cover is gate repair – a bent arm, a bad sensor, a control board that’s acting strangely. That’s a separate line, usually far smaller, and often the smartest first call. We’re Arlington Gate Service, and every job we send a technician to is a gate job. Not a fence job with a gate attached. Not a garage door call. A gate.
Key Takeaways
- A residential gate opener swap in Arlington runs about $950 to $2,800 installed.
- Commercial and heavy-duty slide gate operators run $1,800 to $6,500 or more, depending on weight class and access control.
- Most quotes are driven by gate weight, operator brand, power availability, and safety sensor requirements.
- Diagnosing the actual brand on site matters – we work on nine operator lines, from Mighty Mule and Ghost Controls to FAAC, BFT, DoorKing, and Viking.
- Estimates are free. Call (855) 349-3550. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the numbers break down for a typical Arlington installation. These are estimated ranges for the market as of 2026 – your written estimate is what actually sets the price, because gate weight class and site conditions move the total more than any single part.
| Line Item | Typical Estimated Range |
|---|---|
| Residential swing gate operator (Mighty Mule, Ghost Controls, LiftMaster class) | $950 – $1,900 installed |
| Residential slide gate operator (Linear, Elite, LiftMaster class) | $1,200 – $2,400 installed |
| Commercial-grade slide or swing operator (FAAC, BFT, Viking, DoorKing) | $1,800 – $4,200 installed |
| Heavy-duty commercial operator with access control integration | $3,500 – $6,500+ installed |
| Control board replacement | $250 – $650 |
| Safety sensor pair (photo-eye or edge sensor) | $180 – $500 installed |
| Keypad or access card reader install | $220 – $750 |
| Remote transmitter programming or replacement | $75 – $220 |
| New low-voltage wiring run to the operator | $200 – $900, depending on distance |
| Gate arm or bracket repair | $150 – $550 |
A few things push these numbers up. The heaviest single factor is gate weight: an operator rated for a 400-pound swing gate costs meaningfully less than one engineered for a 2,000-pound slide gate, and commercial properties in Arlington with shared driveways or parking structures usually land in that heavier category. Access control is the second big lever. A plain remote opener is one thing; a DoorKing setup with keypad entry, card readers, and phone-app integration is another job entirely, and the labor to wire and program it adds real cost.
On the other side, an existing gate that’s already plumb, already has power at the post, and just needs a new operator swapped in keeps the total down. That’s the $950 to $1,400 end of the residential range. If the gate itself needs to come off its hinges, the posts need resetting, or power has to be trenched from the house, budget higher. A technician can tell you which side of the line your job sits on after a look at the site.
What Affects Gate Motor & Opener Pricing in Arlington
- Operator brand and weight class. A Mighty Mule residential opener and a FAAC commercial operator aren’t in the same cost universe. The brand your gate needs – or the brand you already have – sets the baseline. We work on nine lines including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we’re pricing the actual unit on your gate, not a generic substitute.
- Gate type: swing versus slide. Slide gates need a track, guide rollers, and usually more operator capacity, so they cost more to automate than a swing gate of similar weight. Swing gates can also need arm geometry work, which adds labor.
- Power at the post. If there’s already a live low-voltage feed at the gate, the install is shorter. If power has to be run from the house or a panel, that’s a trench, a conduit, and extra time. Arlington lots vary a lot here – a close driveway is cheaper to wire than a long setback.
- Safety sensors and code requirements. Automated gates need reversing sensors and proper entrapment protection. This isn’t optional, and it’s a real line item. Ask your city building department about permit requirements for your specific install before work starts.
- Access control complexity. A single remote is cheap. Keypads, card readers, intercoms, and app-based control for an HOA or multi-unit property add wiring and programming time that scales with the number of users.
- Existing gate condition. A structurally sound gate with good hinges and a level track takes a new operator cleanly. A sagging gate or one that’s come off its track needs mechanical repair first, or the new operator will fail early.
One thing worth flagging: electric gate repair is where most Arlington homeowners actually start, not new installation. A gate that won’t open, opens halfway, or reverses for no reason is usually a sensor, a control board, or a limit switch – all small-ticket fixes. We handle the motors, control boards, safety sensors, and access hardware that general contractors typically subcontract out, which means you’re not paying a middleman to route the work.
If your gate is manual right now and you’re considering automating it for the first time, the same estimating applies – we size the operator to the gate and price the full job. If you’re comparing this against other home projects, it helps to know that gate automation is one of the more durable upgrades you can make to a driveway entrance. For properties across Arlington, a working automated gate is also a genuine security improvement, not a cosmetic one.
How to Save on Gate Motor & Opener
You don’t have to take the first number that comes along. A few practical ways to keep the total down:
- Get a real diagnosis before you replace. A gate that won’t open is not always a dead operator. It’s often a $250 control board, a $180 sensor pair, or a $150 arm. Get it diagnosed right the first time instead of swapping a whole motor that didn’t need swapping.
- Match the operator to the gate, not to the biggest model on the shelf. Oversizing an operator for a light residential gate wastes money and can actually cause problems. The right size is the one rated for your gate’s weight with a sensible margin.
- Bundle the access control you actually need. If you’re installing a new operator, adding a keypad now is cheaper than retrofitting one later, because the wiring and programming happen in one visit.
- Fix the gate mechanics while the operator is off. Hinges, rollers, and track work are far cheaper to address during an install than as a separate call a year later.
- Ask for a written estimate that itemizes parts and labor. A clear estimate lets you see where the money goes and decide what’s essential versus what can wait.
Estimates from us are free, and they’re written per job – not a phone-quoted guess. Call (855) 349-3550 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
FAQs – Gate Motor & Opener Cost
How much does a gate opener cost installed in Arlington?
A residential gate opener installed in Arlington runs about $950 to $2,800, and a commercial-grade operator runs $1,800 to $6,500 or more. The range depends on gate weight, brand, whether power is already at the post, and how much access control you need. Call (855) 349-3550 for an exact quote – estimates are free.
Is it cheaper to repair or replace a gate motor?
Repair is almost always cheaper when the problem is a control board, sensor, or limit switch, which typically runs $180 to $650 versus $950 or more to replace a motor. Replacement makes sense when the operator is undersized for the gate, the motor itself is failing, or parts are no longer available for that model. A technician can tell you which situation you’re in after a look at the unit. Call (855) 349-3550 to get it diagnosed.
How much does electric gate repair cost in Arlington?
Most electric gate repairs in Arlington fall between $180 and $650, depending on the failed component. Sensor replacements, control board swaps, and remote programming sit at the low end; wiring faults and access control failures can run higher because they take longer to trace. Call (855) 349-3550 – we’ll give you a written estimate before any work starts.
Do I need a permit to install a gate operator in Arlington?
Permit requirements vary by property and installation, so ask your city’s building department before work begins. Automated gates also need reversing sensors and entrapment protection as a safety matter regardless of permit rules. We can walk you through what your install will involve and flag the questions to ask the city. Call (855) 349-3550 for a free on-site estimate.
Can you work on my specific gate operator brand?
Very likely, yes. We work on nine major operator lines, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, covering everything from light residential driveway openers to heavy commercial systems. That brand range means a technician recognizes the unit on your gate rather than guessing at it. Call (855) 349-3550. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
What Happens When You Call
Tell us the gate type, the brand if you know it, and what it’s doing (or not doing). We’ll set up a free on-site estimate, and a technician will look at the operator, the control board, the safety sensors, and the gate mechanics together – because a motor problem and a gate problem can look identical from the driveway. You’ll get a written estimate that itemizes parts and labor, and the price is set per job by that estimate. No mystery fees, no phone-quoted guesses.
We handle repair and full installation under one roof, so if your existing system is past saving, you’re not sourcing a second vendor to replace it. Homeowners, HOAs, and small business owners across Arlington get the same treatment: a gate specialist who knows the brand on the gate. From the motor to the control board, residential or commercial, it’s the only work we do. Our technicians have up to 10 years of experience with automated and manual gate systems.
Call (855) 349-3550 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Arlington market as of 2026. Arlington Gate Service offers free estimates – call (855) 349-3550.
Written by the team at Arlington Gate Service.
What Our Customers Say
"Second time using them. Same guy, same good work."
- Imani Coleman"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Craig Whitaker"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Katie Hoffman