Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Tysons
Tysons runs on gated property. Office parks off the Dulles Toll Road, gated communities behind them, townhome rows with shared entries – almost every parcel here sits behind a gate. When one fails, vehicles back up fast. We’re gate specialists, not generalists, and we work on the systems that actually run in Tysons: sliding gates, automated operators, wrought iron, wood, and steel. Our technicians have up to 10 years of experience diagnosing the brand in front of them. Call (855) 349-3550. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Tysons Homeowners Call Arlington Gate Service for Gate Repair
Most gate problems in Tysons get misdiagnosed by someone who splits their week across fencing, decks, and garage doors. We don’t. Every job we take is a gate job, which is why we can tell the difference between a bad operator and a track that’s packed with grit.
We handle repair and full installation under one roof. If a system is past saving, you don’t have to find a second vendor. We work on nine operator brands, from residential-grade Mighty Mule and Ghost Controls up to commercial-grade FAAC, BFT, DoorKing, and Viking, so the technician arriving at your property already knows how your system is built.
Tysons sits inside the Capital Beltway with tight interior roads, so access matters. We plan around HOA rules, security vendors, and shared driveways rather than discovering them on arrival. And the humid Mid-Atlantic climate here drives real, seasonal gate problems we see constantly across Tysons.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Sliding Gate Repair in Tysons
Sliding Gate Repair in Tysons is mostly about tight sites. A shared driveway off a route like Route 7 has no room for a swing arc, so the gate slides along the property line and works harder than a swing gate ever would. Tracks collect winter road grit and summer pollen, the operator strains, and the overload trips. Our technicians clear the track, test the travel, and recalibrate the operator so it stops faulting on every pass.
Because these gates often double as property lines in Tysons, a rail that drags can mean a panel is catching a neighbor’s fence or a utility box. We check the whole run, not just the motor.
Rack and Pinion and Track Faults
Most sliding gates in Tysons run a rack and pinion drive. When debris packs into the rack, the teeth wear unevenly and the gate stops mid-travel. We clean the drive, check the rack for worn sections, and adjust the guide rollers so the gate tracks flat.
Loop Detectors and Safety Sensors
A loop detector buried in a Tysons drive can misread after ground movement or pavement work. We test the loop and the safety edges together, because a gate that closes on a phantom reading is a hazard, not just a nuisance.
Wrought Iron Gate Repair in Tysons
Wrought Iron Gate Repair in Tysons shows up most in the newer townhome and condo developments, where ornamental steel and iron gates form the pedestrian and vehicle entries. Weld failures at hinge plates are common, and rust creeps into seams after our wet summers. We re-weld joints, treat rust, realign sagging panels, and get the latch and hinge hardware working together again.
Old, heavy iron gates in Tysons need the operator refitted to match the panel weight once repairs are done. A gate that swings freely by hand takes far less strain off the motor.
Heavy iron panels are dangerous when they come off a hinge. We never suggest homeowners take a loaded gate panel down themselves, and we recommend a trained technician for anything involving a hung gate or an operator under load.
Weld, Rust, and Finish Repair
We re-weld broken joints and treat rust before it spreads into the panel, then refinish so the repair blends with the existing ironwork. On ornamental gates, this keeps the look consistent from the street.
Hinge and Post Realignment
Post movement is the usual cause of a dragging iron gate. We check the post footing, reset the hinges, and confirm the gate clears the ground through its whole swing.
Trusted Brands We Service in Tysons
We work on FAAC, BFT, Linear, and Viking operators, among the nine brands we service. We don’t claim to stock parts – 3-in-1 service. When a Tysons HOA or property manager has a FAAC or BFT gate down, we diagnose the actual failure and get the right part ordered or repaired. A board-level fault in a BFT control panel is not the same job as a worn Linear drive, and treating them the same wastes everyone’s time. We also repair access hardware and wiring, so the door, keypad, and gate all work together.
Common Gate Repair Problems We See in Tysons Homes
- Tracks packed with grit and pollen. Tight shared driveways in Tysons mean sliding gates run right along the pavement, and the track fills fast. The operator strains and trips the overload within a season.
- Wooden swing gates swelling in humid summers. Many 1960s – 1980s homes on the edge of Tysons have cedar or pine gates that bind at the hinge post. They trigger false obstructions right before HOA inspections.
- Access-control integration failures. When a LiftMaster or FAAC operator loses communication with a property-wide system, vehicles strand at the entry until the HOA’s security vendor and a gate technician sort out which side failed.
- Frost heave and post movement. Freeze-thaw cycles in winter push posts up and out, leaving swing gates out of alignment by spring. Adjusting the gate and resetting the post fixes the bind.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Tysons, VA
Gate work in Tysons is quoted per job, not per hour, and the price is agreed before any work starts. A typical hinge and realignment repair runs $150 – $400. Sliding gate track and roller repairs run $200 – $600. Weld and rust repair on a wrought iron gate runs $250 – $750. Operator and control-board diagnostics and repair run $300 – $900, with commercial-grade FAAC and BFT systems at the higher end because access-control integration adds coordination. Full operator replacement runs higher still, and we measure first.
Every estimate is free and written. What moves cost is access – a gate inside a building with limited working space, or one tied into an HOA’s access-control system, takes more time than a simple driveway gate. You’ll know the number before we start, and the written estimate sets the final price.
We Also Serve Cities Near Tysons
We cover Tysons and the neighborhoods around it. If your gate is in Wakefield, Bailey’s Crossroads, George Mason, or Long Branch, we handle those addresses too. The same gate specialists who work the gated communities and office parks along the Toll Road corridor can get to your property. See our full Tysons service area for details on where we work, or call us with your address and gate type.
Serving Tysons, VA – Our Local Coverage Area
We serve Tysons and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Tysons
Yes. A gate technician can diagnose the operator and safety hardware, then coordinate with the HOA’s security vendor when the fault sits in the property-wide access-control system. In Tysons, this coordination is often the whole job, because the gate itself may be fine while the controller is not. Call (855) 349-3550 for a free estimate.
Humidity makes cedar and pine gates swell, and a swollen gate binds against the hinge post. The usual fix is to adjust the hinges and plane the gate, not replace the operator. Call (855) 349-3550 to get it looked at before it strains the motor.
A post that has moved is the most common cause, usually from frost heave or footing settling. Freeze-thaw cycles push posts out of plumb, and the gate follows. We check the footing and reset the hinges. Call (855) 349-3550 for an on-site estimate.
Check the breaker and any manual release before assuming the operator failed. If power is restored and the gate still won’t cycle, it’s likely the control board or a safety sensor. Call (855) 349-3550 – the diagnostic is free, and we’ll tell you what failed.
Yes. We plan the repair around the space you have, and heavy iron panels are handled by trained technicians, never recommended as DIY. We keep the entry working during the visit where possible. Call (855) 349-3550 for an on-site estimate.
Get Your Tysons Gate Working Again
If a gate at your Tysons home, HOA, or business is stuck, dragging, or faulting, call us. We specialize in gates only, from the motor to the control board, and we’ll get it diagnosed right. Call (855) 349-3550 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Arlington Gate Service.