Electric Gate Repair in George Mason - Fixed Today, No Surprise Invoice

Fast, Reliable Electric Gate Repair Across George Mason

If your driveway gate has stopped opening, is dragging at the latch, or the keypad has gone dead, we repair electric gates across George Mason and the surrounding Fairfax County neighborhoods. We’re gate specialists, not generalists: motors, control boards, safety sensors, and access hardware are the only things we work on. That matters in George Mason, where most gates sit on builder-grade ornamental aluminum posts inside HOA-governed subdivisions, and a repair that cycles fine can still fail architectural review if the specs weren’t documented. Call (855) 349-3550 for a free estimate.

Call (855) 349-3550

Why George Mason Homeowners Call Arlington Gate Service for Electric Gate Repair

Most of the gates we see in George Mason were installed by the builder in the 1980s through the 2000s, and they’ve been cycling through Virginia freeze-thaw cycles ever since. When one of those gates stops working, the homeowner usually gets two kinds of advice from general trades: replace the whole thing, or swap the operator. We start by finding the actual fault, which is often neither.

We work on the brands that are actually mounted on George Mason gates, from LiftMaster and Linear residential operators to FAAC and BFT systems on the larger community entries. Our technicians have up to 10 years of experience, and we answer 24/7 with fast dispatch from 7am to 7pm, Sunday through Friday. Because George Mason is an unincorporated community inside Fairfax County rather than its own town, we know to ask which subdivision an address is in before we quote anything, since the HOA design standards vary from one cluster to the next. That single question saves a lot of rejected replacement parts.

Gate Opener Repair in George Mason

Gate opener repair in George Mason usually starts with a simple question: is the opener actually failing, or is it fighting a gate that no longer moves freely? A builder-grade ornamental aluminum swing gate from the 1990s starts dragging at the latch side, and the homeowner assumes the LiftMaster or Linear operator is failing when the real problem is a hinge post that has heaved through repeated freeze-thaw cycles. A qualified technician checks the post footing and plumb before touching the operator, then does sag correction at the hinge post, verifies the safety photocell and loop detector still trip, and documents the panel’s exact color, height and style so any replacement part clears HOA architectural review. Most opener repairs in George Mason run roughly $180 to $420, with control board work at the upper end.

Motor and Gearbox Diagnosis

A motor that hums but doesn’t move, or one that reverses halfway through a cycle, points to a worn gearbox or a limit switch that has drifted. We check the drive train before replacing a motor, because a bound gate will burn out a new motor just as fast as the old one. If the operator is genuinely at the end of its service life, we’ll tell you that plainly.

Keypad and Remote Control Repair

Dead keypads and remotes that only work from ten feet away are usually a receiver, wiring, or battery issue rather than the whole access system. We test the receiver at the operator, check the wiring run to the keypad post, and re-pair remotes where the system allows. If the hardware is obsolete, we’ll explain what a compatible replacement involves.

Automatic Gate Repair in George Mason

Automatic gate repair in George Mason often comes down to a decision about legacy control boards. Older LiftMaster, FAAC and Linear operators in George Mason subdivisions are now old enough that a board-level failure is no longer a part swap: the board is obsolete, and the choice is a retrofit of the control side or a full operator replacement. We diagnose which one actually makes financial sense instead of defaulting to the bigger job. Automatic gate repairs here typically run $220 to $650 when the operator is sound, and a full operator replacement on a residential driveway gate generally lands between $1,400 and $3,200 depending on gate weight, arm or slider type, and whether new safety devices are required.

Safety Sensor and Loop Detector Fixes

A gate that reverses for no reason, or closes on a car sitting on the loop, is a safety device problem more often than an operator problem. We test photocells, edge sensors and loop detectors under actual load rather than just watching the gate cycle once. Gates hung before UL 325 entrapment protection was standard often have no working devices at all, and that has to be corrected before the operator is trusted again.

Access Control and Entry Hardware

Telephone entry systems, card readers and standalone keypads on community entries fail in their own ways, usually at the wiring or the power supply. We trace the low-voltage run and confirm the entry device is talking to the operator before recommending replacement. For multi-unit George Mason properties, that diagnosis step is what keeps a whole entry from being rebuilt for one bad connection.

Trusted Brands We Service in George Mason

We work on FAAC, BFT, Linear and Viking operators, along with LiftMaster, DoorKing, Elite, Ghost Controls and Mighty Mule systems. That range covers everything from light residential driveway arms to heavy commercial slide operators on community entries, and it means the technician arriving at your George Mason gate is likely to recognize the exact model rather than reading a manual on your driveway. We don’t claim to stock parts locally, so turnaround depends on what the diagnosis finds and how quickly the correct part can be sourced. When a board or motor is obsolete, we say so on the first visit rather than ordering something that won’t fit.

Common Electric Gate Repair Problems We See in George Mason Homes

• Heaving hinge posts and sagging panels. Decades of freeze-thaw cycles push posts out of plumb, and the gate binds long before the operator shows a fault. Homeowners frequently replace a healthy operator because of a post problem.
• Obsolete control boards in legacy operators. LiftMaster, FAAC and Linear boards from older installations are no longer manufactured, turning a single component failure into a retrofit-or-replace decision. This is the most common honest conversation we have in George Mason.
• Pre-UL 325 gates with no working safety devices. Gates hung before entrapment protection was standard often have photocells that were never installed or long since failed. Those devices have to work before the gate runs again.
• Fastener corrosion and wood swelling. Original builder-grade aluminum and steel gates show corroded fasteners, and the wooden privacy gates behind some George Mason townhomes swell in humid summers until the latch won’t seat. Both cause intermittent faults that look electrical.

Pricing for Electric Gate Repair in George Mason, VA

We Also Serve Cities Near George Mason

We cover the communities around George Mason as well, including Long Branch, Burke Centre, Wakefield and Braddock. If your gate is in one of those areas, the same technician workflow applies, and the HOA question still comes first. You can read more about our Electric Gate Repair work or see our full coverage for George Mason before you call.

FAQs About Electric Gate Repair in George Mason